Work Sharp Precision Adjust Knife Sharpener
Adjusts from 15° to 30° in 1° steps; cannot preserve an edge below 15°. Maker source.
As an Amazon Associate I earn from qualifying purchases. Some links on this page are affiliate links — if you buy through them, we may earn a commission at no extra cost to you. Disclosure
"Best" here means the closest match to your knives: the knife maker's angle, the knife type and what the sharpener maker allows. Every figure comes from the makers; we don't lab-test sharpeners. How we choose.
A guided system sits between a pull-through and a freehand whetstone. A clamp or a base holds the angle, and you move the abrasive yourself. That means more control over angle and grit than a pull-through, without having to learn to hold an angle by hand.
Adjusts from 15° to 30° in 1° steps; cannot preserve an edge below 15°. Maker source.
Five hones from 70 to 1000 grit and 17°/20°/25°/30° settings; long blades need clamp-width zones. Maker source.
15° or 20° ceramic rods for maintenance; rounded edges support serrations, not fast chip repair. Maker source.
| Model | Angles | Abrasive and grit | Stages | Serrated | Ceramic | Warranty |
|---|---|---|---|---|---|---|
| 15–30° per side, adjustable | tri-brasive rod: diamond + fine ceramic (320 / 600 / fine ceramic) | 3 | with an add-on serration rod (not in the box) | not published | 3 years | |
| 17° and 20° and 25° and 30° per side | alumina oxide ceramic hones (70 / 120 / 280 / 600 / 1000) | 5 | only burr clean-up on the flat side (maker instructions) | not published | not published | |
| 15° and 20° per side | high-alumina ceramic stones (medium + fine) (medium / fine) | 2 | yes — rounded edges of the stones (maker) | not published | not published |
| Work Sharp Precision Adjust | Lansky Deluxe 5-Stone | |
|---|---|---|
| Angles | 15–30°, 1° steps | 17°, 20°, 25°, 30° |
| Abrasives | 320 and 600 diamond, fine ceramic (one rod) | 70, 120, 280, 600, 1000 alumina oxide |
| Long blades | not stated | over 7 in: sharpen in zones (maker) |
| Serrated | add-on rod | burr clean-up only |
| Warranty | 3 years | not published on the product page |
Lansky lists 20° for kitchen cutlery and 17° for "an extremely sharp but delicate edge." If your knives are 15°, only the Work Sharp reaches that setting. Your knife's angle is in the angle finder.
Mid-range · guided (clamp + rod)
Good fit for: any angle from 15° to 30° in 1° steps; matching a maker's factory angle.
| Variant / maker reference | WSBCHPAJ |
|---|---|
| Type | guided (clamp + rod) |
| Angles | 15–30° per side, adjustable |
| Abrasive and grit | tri-brasive rod: diamond + fine ceramic (320 / 600 / fine ceramic) |
| Stages | 3 |
| Serrated knives | with an add-on serration rod (not in the box) |
| Ceramic knives | not published |
| Single-bevel knives | not published |
| Power | manual |
| Warranty | 3 years |
Limits: serrated needs an add-on rod; lowest setting is 15°.
Angle set from 15° to 30° in 1° steps (maker).
Skip it if… your knives are under 15° per side; you want a two-minute sharpener.
Sources: manufacturer page · Checked Nov 18, 2026
Check price on AmazonBudget · guided (clamp + hones)
Good fit for: re-profiling very dull knives (70 grit up to 1000); outdoor and kitchen knives at fixed clamp angles.
| Variant / maker reference | LKCLX |
|---|---|
| Type | guided (clamp + hones) |
| Angles | 17° and 20° and 25° and 30° per side |
| Abrasive and grit | alumina oxide ceramic hones (70 / 120 / 280 / 600 / 1000) |
| Stages | 5 |
| Serrated knives | only burr clean-up on the flat side (maker instructions) |
| Ceramic knives | not published |
| Single-bevel knives | burr clean-up on the unsharpened side (maker) |
| Power | manual |
| Water or oil | honing oil to clean standard hones (maker) |
| Blade limits | blades over 7 in are sharpened in clamp-width zones (maker) |
| Warranty | not published |
Limits: blades over 7 in are sharpened in zones; settings start at 17°.
Skip it if… your knives are 15° or narrower; you sharpen serrated knives.
Sources: manufacturer page · maker support page · Checked Nov 18, 2026
Check price on AmazonMid-range · guided V-rods
Good fit for: serrated knives (rounded edges of the stones); 15° or 20° touch-ups without a clamp.
| Variant / maker reference | 204MF |
|---|---|
| Type | guided V-rods |
| Angles | 15° and 20° per side |
| Abrasive and grit | high-alumina ceramic stones (medium + fine) (medium / fine) |
| Stages | 2 |
| Serrated knives | yes — rounded edges of the stones (maker) |
| Ceramic knives | not published |
| Single-bevel knives | not published |
| Power | manual |
| Warranty | not published |
Limits: ceramic stones only, no coarse diamond; two fixed angles.
Base sets 30° inclusive (15° per side) or 40° inclusive (20° per side) (maker).
Skip it if… your knives are chipped or very dull.
Sources: manufacturer page · Checked Nov 18, 2026
Check price on AmazonIf you'd rather learn freehand, start with whetstones for beginners. The three approaches are side by side on electric vs manual vs whetstone. For chipped edges, Lansky's 70 grit is the coarsest hone on this site; the grit selector lays out the sequence. Need serrated? See serrated sharpeners.
Adjusts from 15° to 30° in 1° steps; cannot preserve an edge below 15°. Maker source.
Five hones from 70 to 1000 grit and 17°/20°/25°/30° settings; long blades need clamp-width zones. Maker source.
15° or 20° ceramic rods for maintenance; rounded edges support serrations, not fast chip repair. Maker source.
Specs verified: November 2026 · Updated 2026-11-18 · How we choose