Do knife sharpeners ruin knives?

As an Amazon Associate I earn from qualifying purchases. Some links on this page are affiliate links — if you buy through them, we may earn a commission at no extra cost to you. Disclosure

A sharpener doesn't ruin a knife on its own. Using it the wrong way does: on a knife it wasn't made for, at the wrong angle, or more often than needed. Every mistake below is one a knife or sharpener maker warns about in its own words.

See relevant tools and maker limits

Avoid the wrong angle, blade type and repair task

A sharp knife or a damaged knife needing professional repair is not a reason to buy another sharpener.

Illustration: two-sided diamond plate (325 and 1200 grit) on a storage base, 14° / 17° / 20° / 25° per side, 6.5 × 3.27 × 1.26 in (L × D × H) from the maker, drawn to the maker's dimensions

SHARPAL 156N Dual-Grit Diamond Whetstone

Check price on Amazon

Its hand-held angle can follow a supported steel bevel; 325/1200 is not permission to repair cracks or broken tips. Maker source.

Illustration: two-layer whetstone (1000 and 6000 grit) on a rubber tray, angle held by hand, dimensions not published by the maker

Shun Combination Whetstone 1000/6000

Check price on Amazon

1000/6000 suits dull unchipped steel, not coarse chip repair; practice angle control before using a valued knife. Maker source.

Mistakes and who warns about them

MistakeWhat the maker saysSource
Electric sharpener on Global knivesGlobal advises against motorized sharpening because it can remove excessive blade materialGlobal (UK)
Sharpening a Cutco Double-D edgeCutco directs Double-D owners back to its factory; home tools and third-party sharpening can damage that edge.Cutco
15° knife in a 20° slot"Do not sharpen 15° knives in Stage 2"Chef'sChoice 4643 manual
Ceramic knives in a steel-knife machineNot for ceramic knives or scissorsChef'sChoice 15XV manual
Non-Kyocera ceramic in Kyocera's sharpener"cannot be sharpened properly"; no warranty when used on themKyocera
Serrated knife on a rolling diamond discThe maker warns that its diamond roller can flatten bread-knife teeth while the teeth may also damage the abrasive discTumbler
Diamond steel for everyday honingShun advises against a diamond steel for regular honing of its knivesShun
Oil or water in a Chef'sChoice electric"do not use honing oils, water or any other lubricant"Chef'sChoice 1520 manual

1. The wrong angle

Every fixed-angle sharpener grinds the edge to its own angle. Put a 14° Wüsthof through a 20° machine and, over a few sessions, you get a 20° knife. That's not broken, but it's no longer the edge Wüsthof made, and you remove extra metal getting there. The same happens in reverse: Chef'sChoice's 15XV converts 20° edges to 15° on purpose. Check your knife's factory figure in the angle finder or the angle guide.

2. Sharpening when honing would do

Shun says sharpening "should be done only when the knife truly needs it," because it removes metal. Honing doesn't. Many "dull" knives only need their edge realigned. The hone-or-sharpen tool helps you tell the difference.

3. Too many passes

Manuals give pass counts for a reason. The 15XV manual describes making pulls until a small burr forms along the full edge, then moving on. It also warns: "Do not over sharpen." Each extra pass on a coarse stage takes metal you didn't need to lose. The Chef'sChoice 4643 manual warns against making many strokes in stage 2 on serrated blades, because it can quickly remove metal from a serrated edge.

4. The wrong knife in the wrong tool

Ceramic knives, serrated knives and single-bevel knives each need a tool whose maker allows them. Chef'sChoice manuals rule out ceramic. Tumbler rules out serrated and ceramic. Kyocera only covers Kyocera ceramic knives. Single-bevel knives get their own procedure in the Chef'sChoice 15XV and 1520 manuals, and Chef'sChoice sends them away from the 4643. The serrated page lists who allows what.

5. Fixing damage the hard way

A chip means removing metal back to below the chip. Shun's service does this for chips of 2 mm or under, and notes that the blade ends up narrower and the edge a little thicker. Bigger chips, cracks or broken tips are better left to the maker or a professional than ground out on a pull-through.

6. Ignoring the warranty and service options

Several knife makers would rather sharpen their knives themselves. Shun sharpens Kai knives free for as long as you own them, and you pay shipping and processing. Cutco requires its Double-D edges to go back to the factory. Kyocera, for its part, says its DS-38 won't sharpen other brands' ceramic knives properly and that no warranty applies when it's used on them. Before you sharpen a knife at home, read what its maker says, which is usually one page on its site.

The short version

  1. Match your knife's factory angle.
  2. Hone first; sharpen only when honing stops working.
  3. Follow the manual's slot and pass counts.
  4. Check that the maker lists your knife type: serrated, ceramic, single-bevel.
  5. Send real damage to the maker.

Electric options that follow these rules are on electric sharpeners, and the trade-offs by type are on electric vs manual vs whetstone.

FAQ

Do electric knife sharpeners ruin knives?
Global (UK) says it doesn't recommend electric sharpeners because they take off too much metal. Other knife makers don't rule them out; Shun accepts one equivalent to its own. Matching the angle and following the manual is what matters.
Are pull-through sharpeners bad?
They grind at a fixed angle. Used at the knife's angle and as the manual says, they do what they're designed to do. Used on the wrong knife or in the wrong slot, they change the edge.

Specs verified: November 2026 · Updated 2026-11-18 · How we choose