HORL HORL 2 Rolling Knife Sharpener
15°/20° magnetic block, diamond disc and ceramic honing; maker excludes serrated blades. Maker source.
As an Amazon Associate I earn from qualifying purchases. Some links on this page are affiliate links — if you buy through them, we may earn a commission at no extra cost to you. Disclosure
"Best" here means the closest match to your knives: the knife maker's angle, the knife type and what the sharpener maker allows. Every figure comes from the makers; we don't lab-test sharpeners. How we choose.
A rolling sharpener splits the job in two. A magnetic block holds the knife at a set angle, and a disc on a roller does the grinding as you roll it along the edge. The angle comes from the block, so the blocks are the first thing to compare.
15°/20° magnetic block, diamond disc and ceramic honing; maker excludes serrated blades. Maker source.
15°/20° holder with diamond and steel honing surfaces; no ceramic, serrated knives or scissors. Maker source.
Four block angles and replaceable discs; the published blade-height range is 0.5–2.25 in. Maker source.
| Model | Angles | Abrasive and grit | Stages | Serrated | Ceramic | Warranty |
|---|---|---|---|---|---|---|
| 15° and 20° per side | diamond disc + ceramic honing disc | 2 | no | yes — hold the angle by hand, since ceramic isn't magnetic (maker FAQ) | not published | |
| 15° and 20° per side | diamond disc + stainless-steel helix honing disc | 2 | no | no | not published | |
| 15° and 17° and 20° and 25° per side | diamond discs + fine ceramic disc (320 / 600 / fine ceramic) | 3 | not published | not published | 3 years |
HORL describes 20° as robust sharpness for sturdy blades like European chef's knives, and 15° as a finer edge for hard carbon or Damascus steel. Its FAQ adds a practical test: try 15° for three to five minutes, and if the sharpness isn't satisfactory, go back to 20°. Better still, start from your knife maker's angle in the angle finder. The full table is on sharpening angles by brand.
Premium · rolling
Good fit for: 15° and 20° knives with a magnetic angle hold; diamond disc needs no replacing when used properly (maker FAQ).
| Variant / maker reference | Walnut (HO2-NUT) |
|---|---|
| Type | rolling |
| Angles | 15° and 20° per side |
| Abrasive and grit | diamond disc + ceramic honing disc |
| Stages | 2 |
| Serrated knives | no |
| Ceramic knives | yes — hold the angle by hand, since ceramic isn't magnetic (maker FAQ) |
| Single-bevel knives | not published |
| Power | manual |
| Water or oil | none — used dry (maker FAQ) |
| Warranty | not published |
Limits: no serrated knives (maker FAQ); ceramic knives need the angle held by hand.
Skip it if… you need to sharpen serrated knives; your knives are under 15° per side.
Sources: manufacturer page · maker support page · Checked Nov 18, 2026
Check price on AmazonMid-range · rolling
Good fit for: straight-edge kitchen knives at 15° or 20°; a simple two-step roll.
| Variant / maker reference | TU01 (wood) |
|---|---|
| In the set | roller with a diamond sharpening disc and a stainless-steel honing disc, plus a magnetic knife holder at 15° or 20° (maker's "What's included") |
| Type | rolling |
| Angles | 15° and 20° per side |
| Abrasive and grit | diamond disc + stainless-steel helix honing disc |
| Stages | 2 |
| Serrated knives | no |
| Ceramic knives | no |
| Single-bevel knives | check the knife maker's instructions (Tumbler FAQ) |
| Power | manual |
| Warranty | not published |
Limits: no serrated, ceramic knives or scissors (maker); single-bevel: check the knife maker first.
From the maker's instructions:
Skip it if… you sharpen serrated or ceramic knives.
Sources: manufacturer page · maker support page · maker support page · Checked Nov 18, 2026
Check price on AmazonMid-range · rolling
Good fit for: four angles: 15°, 17°, 20°, 25°; kitchen and pocket knives.
| Variant / maker reference | WSKTNRKS |
|---|---|
| Type | rolling |
| Angles | 15° and 17° and 20° and 25° per side |
| Abrasive and grit | diamond discs + fine ceramic disc (320 / 600 / fine ceramic) |
| Stages | 3 |
| Serrated knives | not published |
| Ceramic knives | not published |
| Single-bevel knives | not published |
| Power | manual |
| Blade limits | blade width (spine to edge) 0.5–2.25 in (maker) |
| Warranty | 3 years |
Limits: blade width 0.5–2.25 in (spine to edge); serrated use not stated by the maker.
Skip it if… your chef's knife is wider than 2.25 in at the heel.
Sources: manufacturer page · Checked Nov 18, 2026
Check price on AmazonBoth use a two-angle magnetic holder (15° and 20°) with a diamond disc; they differ in the honing disc and in which knives each maker allows. They're head to head on HORL vs Tumbler. For Japanese knives under 15° per side, none of these blocks go low enough; see sharpeners for Japanese knives. For serrated knives, go to serrated sharpeners.
15°/20° magnetic block, diamond disc and ceramic honing; maker excludes serrated blades. Maker source.
15°/20° holder with diamond and steel honing surfaces; no ceramic, serrated knives or scissors. Maker source.
Four block angles and replaceable discs; the published blade-height range is 0.5–2.25 in. Maker source.
Specs verified: November 2026 · Updated 2026-11-18 · How we choose