Honing vs sharpening

As an Amazon Associate I earn from qualifying purchases. Some links on this page are affiliate links — if you buy through them, we may earn a commission at no extra cost to you. Disclosure

A knife that feels dull is often not worn out. Its edge has simply rolled over. Honing pushes it back. Sharpening grinds away metal to make a new edge. Knowing which one you need saves steel, and saves the knife.

See relevant tools and maker limits

If honing no longer brings the edge back, these sharpen at the angle your knives need

If honing brought the edge back, keep using your hone; these are for when it no longer does.

Illustration: small manual sharpener with two slots and a contoured base, 20° per side, dimensions not published by the maker

Work Sharp Kitchen Edge Knife Sharpener

Check price on Amazon

The fine ceramic wheel maintains supported edges; the separate carbide sharpening slot is fixed at 20°. Maker source.

Illustration: two-layer whetstone (1000 and 6000 grit) on a rubber tray, angle held by hand, dimensions not published by the maker

Shun Combination Whetstone 1000/6000

Check price on Amazon

1000 removes metal to restore a dull edge and 6000 refines it; this is not a non-abrasive honing steel. Maker source.

Honing versus sharpeningHoning pushes a rolled edge back into line without removing metal. Sharpening grinds new facets, removing metal to make a new edge. Honing rolled edge back in line no metal removed Sharpening worn, rounded new facets metal removed (dashed)

What the makers say

HoningSharpeningSource
What it does"realigns the microscopic teeth on the edge"removes some blade material to form a replacement cutting edgeWüsthof
Metal removed"does not create a new edge, and it does not remove metal"takes away blade material, so reserve it for an edge that actually requires sharpeningShun
How oftenonce a week to every day, by useabout once a year for many home cooksShun
How oftenevery few usesonce or twice a yearVictorinox
How oftenweeklytwo to three times a yearGlobal (UK)

Honing: keep the edge in line

In use, a fine edge bends to one side. It still has plenty of metal; it just isn't pointing straight down anymore. A honing steel pulls it back into line. Wüsthof's instructions: rest the steel's tip on a non-slip surface, tilt the knife to 14° (10° for Asian-style knives), and draw it from heel to tip, alternating sides six to eight times. Shun builds a 16° guide into the hand guard of its steel. Victorinox says to hold the blade at 20° to the steel.

Not every rod is a honing rod. Shun separates the two clearly: its honing steel "won't take material off your blade," while its ceramic rod "will take material off" and should be used "more sparingly." Shun also warns against using a diamond steel for regular honing on its knives. Wüsthof sells both honing steels and sharpening steels. It suggests honing on a steel as routine upkeep and switching to a sharpening steel once the edge needs resetting.

Sharpening: make a new edge

When honing doesn't bring the edge back, the edge itself is worn: rounded, chipped or too thick. Then you need to remove metal, on a stone, a guided system, a pull-through or an electric. Shun puts the switch point simply: A dull blade that no longer improves with honing needs its edge sharpened. Sharpening at the knife maker's angle keeps the edge geometry the same. The angle finder shows that angle for your brand.

A simple routine

  1. Feels dull? Hone first, at your knife's angle.
  2. Test it. Slice a sheet of paper; the Chef'sChoice 4643 manual says a sharp edge should cut it smoothly. More tests in how to tell if a knife is sharp.
  3. Still dull? Sharpen. The grit selector or the sharpener finder helps.
  4. Chipped, cracked or a broken tip? See hone or sharpen. Large damage goes to the maker or a pro.

Common mix-ups

Why it matters

Every sharpening shortens the life of the blade a little. Honing doesn't. A knife that's honed regularly needs sharpening less often, which is the point of Shun's "hone for maintenance, sharpen for restoration." The schedules makers suggest are compared in how often to sharpen. The ways a sharpener can remove too much metal are in do knife sharpeners ruin knives?.

FAQ

Does a honing steel sharpen a knife?
A plain honing steel doesn't. Shun says honing doesn't create a new edge and doesn't remove metal. Shun adds that its ceramic rod does take material off, so it sharpens as well as hones.
How often should I hone?
Shun says some cooks hone once a week and others every day, depending on use. Victorinox suggests honing every few uses; Global's UK site says weekly.

Specs verified: November 2026 · Updated 2026-11-18 · How we choose