Whetstone grit chart

As an Amazon Associate I earn from qualifying purchases. Some links on this page are affiliate links — if you buy through them, we may earn a commission at no extra cost to you. Disclosure

The grit number tells you how coarse a stone is: low numbers cut fast and leave a rough edge, high numbers cut slowly and leave a fine one. A sharpening session goes from coarse to fine, starting only as coarse as the edge needs.

See relevant tools and maker limits

Numbers belong to the maker’s scale

Illustration: two-sided diamond plate (325 and 1200 grit) on a storage base, 14° / 17° / 20° / 25° per side, 6.5 × 3.27 × 1.26 in (L × D × H) from the maker, drawn to the maker's dimensions

SHARPAL 156N Dual-Grit Diamond Whetstone

Check price on Amazon

325 diamond is published as 45 microns and 1200 as 12 microns; used dry, not a water stone. Maker source.

Illustration: two-layer whetstone (400 and 2000 grit) in a holding tray, angle held by hand, dimensions not published by the maker

WÜSTHOF Whetstone J 400/2000

Check price on Amazon

400/2000 combination spans unevenness repair and refinement after soaking; no invented cross-brand grit conversion. Maker source.

Grit ladder from coarse to fineA ladder of grit numbers used by the stones in this site: 70, 120, 280, 325 and 400 are coarse for repair and reshaping; 600, 1000 and 1200 are medium for regular sharpening; 2000 and 6000 are fine for refining and polishing. CoarseMediumFine 70 · 120 · 280Lansky hones 325Sharpal diamond 400Wüsthof stone 600Lansky, Work Sharp diamond 1000Shun stone, Lansky 1200Sharpal diamond 2000Wüsthof stone 6000Shun stone Removes more metal ← → leaves a finer edge. Bands are our grouping; scales differ between makers.

The chart

GritBandWhat the maker says it's forStone
70 / 120CoarseExtra coarse / coarse; start here for a very dull edge or a new angleLansky Deluxe
280CoarseLansky calls it Medium; start here for touch-ups on that systemLansky Deluxe
320Coarse"Coarse" diamond on the RKS discs; diamond face of the Precision Adjust rodWork Sharp
325 (45 microns)Coarse"restore a dull or damaged edge"Sharpal 156N
400Coarse"smooth off any unevenness"Wüsthof J 400/2000
600MediumFine (Lansky); fine diamond (Work Sharp)Lansky, Work Sharp
1000Mediumrestoring dullness (Shun); ultra fine on Lansky's systemShun 1000/6000
1200 (12 microns)Mediumfor honingSharpal 156N
2000Finefiner side "used to hone and sharpen"Wüsthof J 400/2000
6000Fine"refresh and polish the edge"Shun 1000/6000

The bands (coarse up to 400, fine from 2000) are our grouping, not a standard. Makers grade differently: Lansky calls 280 "medium" and 1000 "ultra fine," while Shun treats 1000 as the stone for a dulled edge. Read each stone's number with its maker's description.

How to use the chart

  1. Chipped or uneven edge: start coarse (325–400, or 70–120 on a Lansky). Work until a burr forms along the full edge, then go up through the bands.
  2. Dull, no damage: start medium (around 1000), finish fine.
  3. Lost its bite: a fine grit alone may be enough. Hone first, though; see honing vs sharpening.
  4. Polish: after medium, finish at 6000.

The grit selector does this with your own stones and tells you which bands your set is missing. The burr check that decides when to move up is described in how to tell if a knife is sharp.

How long to stay on each grit

There's no fixed count. Stay on a grit until it has done its job along the whole edge, then move up. On the coarse and medium stones, the sign is a burr you can feel along the full length. On the fine stones, it's a smooth, even scratch pattern and a clean paper cut. Moving up too early leaves deep scratches the finer stone can't remove. Staying on a coarse grit too long removes metal you didn't need to lose. The 15XV manual's warning about electric stages applies to stones too: "Do not over sharpen." Most routine sessions never touch the coarse band. Makers' schedules are in how often to sharpen.

Water, oil or dry

Stones differ here too. Shun says to soak its stone before use. Wüsthof says to submerge its stones for about ten minutes, until no more air bubbles rise. Sharpal's diamond plate is used dry: "No messy oil needed." Lansky's alumina oxide hones don't need oil, but Lansky suggests a few drops to lift metal filings when the stone starts to clog. HORL's diamond disc is also used dry.

Diamond or water stone?

Diamond plates (Sharpal 156N) stay flat and don't need soaking. Water stones (Shun, Wüsthof) are what most Japanese-style sharpening guides start with. Both are on whetstones for beginners. For a fixed-angle alternative, see whetstone vs electric.

FAQ

Is 1000 grit enough?
For regular sharpening, often yes. Shun calls its 1000 side the one for restoring a dulled edge. A finer stone (Shun pairs it with 6000) refines and polishes. Chips need a coarser grit.
1000 vs 6000 grit: what's the difference?
Shun's combination stone uses 1000 to restore a dulled edge and 6000 to refresh and polish it. The 6000 side doesn't repair a dull edge on its own.

Specs verified: November 2026 · Updated 2026-11-18 · How we choose